Sponsored Ads |
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
08-21-2011, 08:02 PM
|
#11
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
Originally Posted by Redtruck-VA
usually BJ's are all changed out. Check them out and see if you can replace just the BJ's or do you have to change to whole control arm. If it is revited you can use a hand grinder to knock the heads off. Good luck..
|
Both the tops and lowers are pressed in on mine....I cant grease them, cause they are the factory ones with no zerk fittings.
|
|
|
|
08-21-2011, 08:07 PM
|
#12
|
N.C. Chapter President
Join Date: Nov 2010
Location: Salisbury, North Carolina
Name: Jim
Age: 77
Posts: 2,683
|
Hope you get rid of the creaking; gotta be annoying. Those shocks are darn good ones; used that type on several of my vehicles over the years.
|
|
|
|
08-21-2011, 08:17 PM
|
#13
|
Florida Chapter Vice President
Join Date: Jan 2011
Location: FL
Name: Daniel
Age: 37
Posts: 3,354
|
Yeah I was wondering if that was gonna work because greg said something about it in my thread.
|
__________________
2013 Chrysler 300C
2010 Avenger (REVENGE)
|
|
|
08-21-2011, 08:22 PM
|
#14
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
If they are pressed in then they will need to be pressed out. Do you have anyone that can press them out? Some parts stores can do it,
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
08-21-2011, 09:43 PM
|
#15
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
Originally Posted by Redtruck-VA
If they are pressed in then they will need to be pressed out. Do you have anyone that can press them out? Some parts stores can do it,
|
I can get a ball joint press using Autozones Loan A Tool deal...only cost $5 to rent it I think...
for what it's worth, here is a pic of my old shocks...Mopar SVT stockers...
|
|
|
|
08-21-2011, 10:08 PM
|
#16
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
I'd say you got your money's worth out of the old shocks. lol
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
08-21-2011, 10:15 PM
|
#17
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
for real....
Greg, all the creaking is coming from my drivers side, can I just replace the ball joints on that side?
|
|
|
|
08-21-2011, 10:22 PM
|
#18
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
Originally Posted by 96MagnumRam
for real....
Greg, all the creaking is coming from my drivers side, can I just replace the ball joints on that side?
|
Yes, but you are suppose to have the front end aligned after changing them, so most folks change them all at the same time.
You can jack the wheel off the ground about three inches and put a pry bar under the tire and pull up on the bar to see which of the joints is loose. Good luck..
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|