Sponsored Ads |
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
07-02-2011, 11:34 PM
|
#1
|
SRT Member
Join Date: Nov 2010
Location: Oklahoma
Name: Colton
Age: 29
Posts: 1,513
|
Coil springs
I just saw on a show that cutting the coil springs would lower the ride. Would that be a good way to go? Remember I like the cheap way lol and this is it. Just want to know if it would be a good way to do it
|
__________________
|
|
|
07-02-2011, 11:41 PM
|
#2
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
The recommended method is to use drop spindles to lower a vehicle. This maintains the stock geomentry. Coils can then be trimmed to adjust the final drop. Get cheap out of your mind, think quality and you will save time and money in the long run.
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
07-02-2011, 11:44 PM
|
#3
|
SRT Member
Join Date: Nov 2010
Location: Oklahoma
Name: Colton
Age: 29
Posts: 1,513
|
True... So what would happen if I did do that?
|
__________________
|
|
|
07-02-2011, 11:55 PM
|
#4
|
Vertically Challenged Super Mod
Join Date: Oct 2010
Location: Collinsville, OK
Name: Michael
Age: 44
Posts: 2,700
|
Cutting your springs will make you wheels angle inward causing rubbing and premature wear, it will also make your truck ride like crap. Just save up for the kit, a few more tile jobs will do it
|
|
|
|
07-02-2011, 11:58 PM
|
#5
|
SRT Member
Join Date: Nov 2010
Location: Oklahoma
Name: Colton
Age: 29
Posts: 1,513
|
Hell yeah! That would be cool
|
__________________
|
|
|
07-03-2011, 12:04 AM
|
#6
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
Lowered springs have a higher spring rate than the OEM spring. This helps to counter the reduced travel of a shorter spring. Bumps stops are normally removed and replaced with a aftermarket one that is custom fitted. Cutting a OEM spring as stated reduces travel and knocks the alignment out of spec, sometimes to a degree that makes it very difficult to get aligned. Adjusters are often required and cost about $50 for each side, Plus a custom alignment that can cost around $200 when having the adjusters installed usually without a gurantee. If the alignment isn't done correctly you will chew up tires and it may be dangerous to drive. My advice is do it right the first time and be done with it. Dropped rides have many advantages. Good luck...
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
07-03-2011, 12:06 AM
|
#7
|
SRT Member
Join Date: Nov 2010
Location: Oklahoma
Name: Colton
Age: 29
Posts: 1,513
|
Ok I'm talked out of it now lol I'll just save up and do it later on down the road
|
__________________
|
|
|
07-03-2011, 12:16 AM
|
#8
|
Turbo Member
Join Date: Feb 2011
Location: Virginia/Philippines
Name: PI_greg
Posts: 1,370
|
Lowered trucks are great fun to drive. You will like it..
|
__________________
PI_greg 2003 SXT-Hemi, SS/T rims, 275/60-17, AeroForce, w/wideband, 6.1 ignition, K&N-77 CAI, Fastman TB, eFan, 180 stat, TMR, HD OEM Trans Cooler, SC3865/PSC1, Dual window switch/ high idle mod, Edge, Crazy Spartan (112 lsa), 2800, DTT 4:10, TCI Floor Shifter, Shift lite, Pacesetter Ceramic LT's, Magna Spun Cats/SI/DO Muffler, Mcgaughys 2/4.5 spindle kit, Monroe shocks, Caltracs, Aeon springs bumps, SRT-10 gage pillar, air horn
|
|
|
07-03-2011, 12:18 AM
|
#9
|
SRT Member
Join Date: Nov 2010
Location: Oklahoma
Name: Colton
Age: 29
Posts: 1,513
|
Looking forward to it!
|
__________________
|
|
|
07-12-2011, 04:38 PM
|
#10
|
V6 Member
Join Date: Aug 2010
Location: Crystal River, FL
Name: Patrick
Age: 35
Posts: 406
|
I went with belltech 2" drop coils on my Ram Sport. Loved them Stiffened up the ride some and made taking corners more fun.
|
__________________
![](http://i54.photobucket.com/albums/g114/RiggsAlstott3340/Corvette-1.jpg)
Save the wave! ![Wave](https://www.semopar.com/images/smilies/wave.gif)
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Drop springs
|
Redtruck-VA |
Wanted |
5 |
05-30-2011 03:17 PM |
6.1 dual coil ignition mod
|
Redtruck-VA |
Engine & Performance |
10 |
04-17-2011 07:57 PM |
|