Sponsored Ads |
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
Photo's & Video's Post your photo's & video's here. |
03-25-2011, 05:16 PM
|
#1
|
Newb
Join Date: Dec 2010
Location: Boston
Name: Jimmy
Posts: 100
|
Installed - Fatmat'd ENTIRE Floor
Well I decided before the season starts that I'll get some mods done. One of them is finishing up installing fatmat to the floor and roof. I decided to hold off on the roof, due to the headliner being a pita to take out, so I'm doing the entire floor and door jams. If you look, you'll see my other thread on fatmat'n all 4 doors outer shell, entire trunk, decklid, rear fenders and rear deck. That made a huge difference already with my stock mtx system, road noise and made all parts covered solid. You can hear the diff when you close the doors.
Here are a few pix with the interior floor gutted out,
![](http://i166.photobucket.com/albums/u99/BosChargerSRT/1900c44c.jpg)
Will be vacuuming today and wiping area clean. Should be starting laying fatmat down later today and hope to finish by the weekend.
I also recently bought a used VES, which came with a broken harness, which was a pita and had to swap harness blocks. All is good and worked awesome.
|
__________________
Jimmy
CarbonbyDesign, Billet Tech Designer, Razor's Edge, SpeedLogix, KW v2, Predator 91 tune, 22" 3 pc Covet Forged Wheels , Nitto 420s, BWoody Sway endlinks, Hotchkis sways, Magnaflow highflow/mod c-back, DMH electric cutouts, 22elite, BND ALL Quantum Blue/ACESIV, Killerglass, ABG roof lip, GSM intake, Danko v2 spoiler, tinted corner/tails, Neffywrap
|
|
|
03-25-2011, 05:17 PM
|
#2
|
Newb
Join Date: Dec 2010
Location: Boston
Name: Jimmy
Posts: 100
|
|
__________________
Jimmy
CarbonbyDesign, Billet Tech Designer, Razor's Edge, SpeedLogix, KW v2, Predator 91 tune, 22" 3 pc Covet Forged Wheels , Nitto 420s, BWoody Sway endlinks, Hotchkis sways, Magnaflow highflow/mod c-back, DMH electric cutouts, 22elite, BND ALL Quantum Blue/ACESIV, Killerglass, ABG roof lip, GSM intake, Danko v2 spoiler, tinted corner/tails, Neffywrap
|
|
|
03-25-2011, 05:39 PM
|
#3
|
Vertically Challenged Super Mod
Join Date: Oct 2010
Location: Collinsville, OK
Name: Michael
Age: 44
Posts: 2,700
|
wow that looks awesome.
|
|
|
|
03-25-2011, 05:54 PM
|
#4
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
Is that stuff basically a peel and stick? That looks like a good weekend job with having to pull everything out of the car like that...looks good BOS
|
|
|
|
03-25-2011, 07:42 PM
|
#5
|
Newb
Join Date: Dec 2010
Location: Boston
Name: Jimmy
Posts: 100
|
Originally Posted by OklaHemi
wow that looks awesome.
|
Originally Posted by 96MagnumRam
Is that stuff basically a peel and stick? That looks like a good weekend job with having to pull everything out of the car like that...looks good BOS
|
Yeah, peel and lay. Thanks fellas!!
|
__________________
Jimmy
CarbonbyDesign, Billet Tech Designer, Razor's Edge, SpeedLogix, KW v2, Predator 91 tune, 22" 3 pc Covet Forged Wheels , Nitto 420s, BWoody Sway endlinks, Hotchkis sways, Magnaflow highflow/mod c-back, DMH electric cutouts, 22elite, BND ALL Quantum Blue/ACESIV, Killerglass, ABG roof lip, GSM intake, Danko v2 spoiler, tinted corner/tails, Neffywrap
|
|
|
03-30-2011, 03:16 PM
|
#6
|
V6 Member
Join Date: Aug 2010
Location: Crystal River, FL
Name: Patrick
Age: 34
Posts: 406
|
Hey Jimmy how much does that stuff run? I am considering doing my entire interior with it. I have also heard peal and seal from Lowes works well too.
|
__________________
![](http://i54.photobucket.com/albums/g114/RiggsAlstott3340/Corvette-1.jpg)
Save the wave! ![Wave](https://www.semopar.com/images/smilies/wave.gif)
|
|
|
03-30-2011, 08:29 PM
|
#7
|
N.C. Chapter President
Join Date: Nov 2010
Location: Salisbury, North Carolina
Name: Jim
Age: 77
Posts: 2,683
|
Nice job on the install Jimmy ~ looks great and I'm sure your sound will be so much better!
|
|
|
|
03-31-2011, 10:39 AM
|
#8
|
V6 Member
Join Date: Sep 2010
Location: Miami, FL
Name: Jordan
Age: 34
Posts: 479
|
I have always been a fan of fatmat, the same thing as dynamat but much more economical and it just looks great in my opinion. Great job putting it in there Jimmy it looks great.
And Patrick that stuff is much more economical than dynamat, here is a link to their site, it depends on how much you want and the thickness, thats where the prices will vary a lot
http://www.fatmat.com/
I want to fatmat the whole enterior of my 1962 Galaxie, I've had that idea for a pretty long time now, so as soon as I get a little extra cash flow and finish up all the metal work that needs to be done (just a few minor touches) I will see if i get that in there.
|
|
|
|
03-31-2011, 10:40 AM
|
#9
|
V6 Member
Join Date: Sep 2010
Location: Miami, FL
Name: Jordan
Age: 34
Posts: 479
|
You can get 100 sq. ft. of fat mat in a kit with the roller and a blade and stuff for 129.99
|
|
|
|
03-31-2011, 11:38 PM
|
#10
|
V6 Member
Join Date: Aug 2010
Location: Crystal River, FL
Name: Patrick
Age: 34
Posts: 406
|
Thanks Jordan!
|
__________________
![](http://i54.photobucket.com/albums/g114/RiggsAlstott3340/Corvette-1.jpg)
Save the wave! ![Wave](https://www.semopar.com/images/smilies/wave.gif)
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|