Sponsored Ads |
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
03-24-2011, 08:50 PM
|
#1
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
Doing my own exhaust
So, with money being a little tight, I figured I would do my own exhaust in Ruby, rather than paying someone $200 to do it...the only thing is...I HAVE done my own exhaust in my S10, however, didnt have to deal with a down stream O2 on it, being it was an OBDI system....
Now, my plan is to run a Cherry Bomb extreme, then dump it...what do I do with the downstream sensor?
|
|
|
|
03-24-2011, 08:53 PM
|
#2
|
President - Admin
Join Date: Aug 2010
Location: Tampa Bay
Name: Jay
Age: 44
Posts: 5,251
|
i think you can just wrap it in tin foil and zip it up next to the frame, im not possitive but maybe pm silverbullet i think he did it...my down stream is before the exhaust i believe....
|
__________________
'04 Murdered 1500 (His)
'12 Journey Storm (Hers)
|
|
|
03-24-2011, 09:05 PM
|
#3
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
I didnt really pay attention to where mine was...so I dont really know if it is the intermediate pipe between the cat and stock muffler or behind the actual muffler itself...if need be I can get an intermediate 2.5 inch pipe and have the muffler shop weld an O2 bung in it...but my original plan was to dump the outlets off the cherry bomb itself, rather than using a pipe between the muffler and dumps
|
|
|
|
03-24-2011, 09:09 PM
|
#4
|
President - Admin
Join Date: Aug 2010
Location: Tampa Bay
Name: Jay
Age: 44
Posts: 5,251
|
make sure it dumped under the bed....
|
__________________
'04 Murdered 1500 (His)
'12 Journey Storm (Hers)
|
|
|
03-24-2011, 09:13 PM
|
#5
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
It should be honestly...now that I think about it...if the O2 is in the intermediate pipe, then all I would have to do is unclamp the stock muffler, clamp on the cherry bomb then dump it...
|
|
|
|
03-24-2011, 09:54 PM
|
#6
|
Florida Chapter Vice President
Join Date: Jan 2011
Location: FL
Name: Daniel
Age: 37
Posts: 3,354
|
Originally Posted by 96MagnumRam
It should be honestly...now that I think about it...if the O2 is in the intermediate pipe, then all I would have to do is unclamp the stock muffler, clamp on the cherry bomb then dump it...
|
Exactly
|
__________________
2013 Chrysler 300C
2010 Avenger (REVENGE)
|
|
|
03-24-2011, 10:29 PM
|
#7
|
V8 Member
Join Date: Nov 2010
Location: Texarkana, TX
Name: Mark
Age: 36
Posts: 697
|
Originally Posted by 96MagnumRam
It should be honestly...now that I think about it...if the O2 is in the intermediate pipe, then all I would have to do is unclamp the stock muffler, clamp on the cherry bomb then dump it...
|
If yours is anything like mine, the o2 sensor is before the cat in the intermediate and the muffler is welded
|
|
|
|
03-24-2011, 10:30 PM
|
#8
|
V6 Member
Join Date: Aug 2010
Location: Crystal River, FL
Name: Patrick
Age: 35
Posts: 406
|
Yeup, all you have to do is unclamp the old exhaust and bolt on a new. However, I would eventually get it welded to prevent any leaks. Clamps will rust and break eventually.
|
__________________
![](http://i54.photobucket.com/albums/g114/RiggsAlstott3340/Corvette-1.jpg)
Save the wave! ![Wave](https://www.semopar.com/images/smilies/wave.gif)
|
|
|
03-24-2011, 11:56 PM
|
#9
|
R/T Member
Join Date: Aug 2010
Name: Nick
Age: 34
Posts: 983
|
yea i had my rear o2s wrapped in foil and thrown in the heat duct on mine truck no codes for me
|
__________________
![](image.php?u=5&type=sigpic&dateline=1338927444)
The Legend Returns
|
|
|
03-25-2011, 12:45 AM
|
#10
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
Originally Posted by txbass06
If yours is anything like mine, the o2 sensor is before the cat in the intermediate and the muffler is welded
|
Not welded on mine...just has your standard run of the mill exhaust clamps where the intermediate pipe slides into the muffler.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Exhaust, Again..
|
BassMaster |
Engine & Performance |
5 |
03-11-2011 08:19 PM |
Exhaust
|
BassMaster |
Engine & Performance |
34 |
02-12-2011 12:42 AM |
Exhaust setups
|
redneckrocket38 |
Engine & Performance |
23 |
01-19-2011 12:53 PM |
My Exhaust
|
Onk |
Photo's & Video's |
0 |
10-23-2010 12:12 PM |
Exhaust Differences
|
004x41500 |
FAQ'S |
0 |
10-18-2010 03:29 AM |
|