Sponsored Ads |
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
<<<<<< Register to remove these ads >>>>>>
|
|
01-06-2011, 03:48 PM
|
#1
|
R/T Member
Join Date: Oct 2010
Location: Sebastian, Florida
Name: Cory
Age: 33
Posts: 816
|
Trans temp gauges?
so im eventually gonna order gauges from glow shift, and i have considered doing 2 trans temps, and an oil temp.
i want to put a sensor in the "hot" line out to the cooler, and 1 in the #4 test port (i think thats the one) this way i could look and see what my output temps are, and what my case is running at as well.
anyone have any thoughts on this?
it wont cost me any extra to do the dual trans temps. since im goin with the pillar pod combo.
|
__________________
'01 Silver Ram 1500 4x4 SLT Off Road Quad Cab 5.9L Auto
Ya, it wants to be a 6 cylinder...Cummins that is.
My name is Ram, and I wish I was a 24v cummins.
|
|
|
01-06-2011, 03:52 PM
|
#2
|
R/T Member
Join Date: Aug 2010
Name: Nick
Age: 34
Posts: 983
|
test port #3 is where i have mine in
|
__________________
![](image.php?s=5ed7ad17abdf4e6926f9e129edf948a9&u=5&type=sigpic&dateline=1338927444)
The Legend Returns
|
|
|
01-06-2011, 04:04 PM
|
#3
|
SRT Member
Join Date: Aug 2010
Location: Oviedo
Age: 35
Posts: 1,603
|
Im planning on doing a glowshift 3in1 diesel gauge. I was told you could use those clamp on senders or drill a hole in the pan and or remove a bolt and put the sensor in there. Im assuming that bolt is the "Test port"???
|
__________________
|
|
|
01-06-2011, 04:04 PM
|
#4
|
R/T Member
Join Date: Oct 2010
Location: Sebastian, Florida
Name: Cory
Age: 33
Posts: 816
|
ya, i googled it, and found your diy on 3 different sites. though i thought it was different on the 2nd gens with the 46re trans?
what do you think of running dual trans temps?
|
__________________
'01 Silver Ram 1500 4x4 SLT Off Road Quad Cab 5.9L Auto
Ya, it wants to be a 6 cylinder...Cummins that is.
My name is Ram, and I wish I was a 24v cummins.
|
|
|
01-06-2011, 04:15 PM
|
#5
|
SRT Member
Join Date: Aug 2010
Location: Oviedo
Age: 35
Posts: 1,603
|
Isnt one line coming from the coole,r cooling down the fluid then the other one releaseing the fluid from the trans to the cooler. Wouldnt it be better to monitor the fluid coming out of the trans that way you know if the trans is overworking, overheating etc.
|
__________________
|
|
|
01-06-2011, 04:23 PM
|
#6
|
R/T Member
Join Date: Oct 2010
Location: Sebastian, Florida
Name: Cory
Age: 33
Posts: 816
|
Originally Posted by 03 rammer
Isnt one line coming from the coole,r cooling down the fluid then the other one releaseing the fluid from the trans to the cooler. Wouldnt it be better to monitor the fluid coming out of the trans that way you know if the trans is overworking, overheating etc.
|
thats one of the 2 im considering. im gonna put a t in the line that goes out to the cooler. the "hot" line. im still not sure if i want to run 2 trans temp gauges, we just got a new camper, 1997 26' Jayco Tandems Elec. brakes, 4800# now im not gonna think about pulling it, not until i swap my gears first. which i decided im gonna stick with the 33s and no lift, and go with 4.56s that way i know ill have plenty of torque and power to pull it without burning my trans up. though i do think it would be a smart choice to run dual tran temps, that way i know what the trans case it running at, and what the fluid going out to the cooler is running at. i seen that one guy had done this with 1 gauge and 2 senders, but put a switch to switch between them, though i really dont like that idea, and i thought it would be better to just run 2 seperate gauges, and label them acordingly. (ie. Case, and Line)
|
__________________
'01 Silver Ram 1500 4x4 SLT Off Road Quad Cab 5.9L Auto
Ya, it wants to be a 6 cylinder...Cummins that is.
My name is Ram, and I wish I was a 24v cummins.
|
|
|
01-06-2011, 04:51 PM
|
#7
|
SRT Member
Join Date: Aug 2010
Location: Oviedo
Age: 35
Posts: 1,603
|
That does sound smart since you will be towing alot also I've head of guys having a dif temp gauge just because they tow soo much.
|
__________________
|
|
|
01-06-2011, 04:57 PM
|
#8
|
Super Moderator
Join Date: Oct 2010
Age: 45
Posts: 6,570
|
I would like to know how this works out for you if you do it soon...cause I am having some trans work done and would like to have these installed while the guy is there.
|
|
|
|
01-07-2011, 08:55 AM
|
#9
|
Banned
Join Date: Dec 2010
Location: Look out front,.. See the tire smoke???
Name: ^^
Age: 37
Posts: 1,550
|
I think the output temp will scare you... Why do you want to see what your output temp is anyway? Aslong as you know what it's running inside the tran's, all is gravy.
In my '86 and '98, I tapped right into the driver's rear corner of the pan. No leakage and read's perfect.
|
|
|
|
01-07-2011, 12:44 PM
|
#10
|
R/T Member
Join Date: Oct 2010
Location: Sebastian, Florida
Name: Cory
Age: 33
Posts: 816
|
on your 98 what readings were you getting?
|
__________________
'01 Silver Ram 1500 4x4 SLT Off Road Quad Cab 5.9L Auto
Ya, it wants to be a 6 cylinder...Cummins that is.
My name is Ram, and I wish I was a 24v cummins.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|